Description
A-One Winter Care
AUTOMATIC CONTROL ELECTRIC BLANKET WITH MEMORY PROGRAMMING
Timer – The user can set the time after which the blanket will switch off just like an AC. The user can set the time in the range of 60 minutes to 480 minutes, gap of 60 minutes.
Temperature Setting -The user can set the desired temperature digitally in the range of 24 oC to 60 oC temperature just like operating an AC.
Automatic feature-
The automatic feature is designed to conserve the energy. The blanket turns off automatically as it reaches the set temperature and begins heating again as the temperature falls. This feature also enables the blanket to shut down after the set time duration.
MEMORY PROGRAMMING – If due to power failure the blanket loses power during use, the blanket will save its last settings.It will resume its heating operations as set by the user before the power went off as if there were no interruptions!
- NEWSLEEPING CONCEPT a revolutionary way.
- Most Convenient and economical way of keeping a person warm
- Useful for Arthritics/Old Age Pains.
- LED Indicator for Clear Viewing.
- Even Distribution of Heat.
- Water Proof Element Teflon Coated for complete protection
- Complete insulated on either side for complete safety and comfort.
Our product A-One Winter Care Electric Blanket were carefully designed to provide uniform and gentle warmth. It is a perfect night-time companion during intolerable cold winter nights. It will provide long term cost efficient comfort. This product is highly recommended for elders with old-age pains and people with aches and pains.
| SIZE | Power consumption per hour | |
| 36” x 72” | 90 watt | Automatic Control |
| 75” x 72” | 180 watt | Automatic Control |
| 72” x 60 “ | 150 watts | Automatic Control |
The products are exclusively designed for warming of the bed, taking 20-25 minutes to reach optimum temperature. The blankets operate on 220-250 VAC, 50-60 Hz
Guidelines:
The Digital control is designed to notify you in case there is some problem with your heating product.The controller notifies you by displaying “Er” on the display. In such a case, follow the following steps:
- Check the blanket is well connected with the controller
- Switch off/on the power supply again
- Check that the system is well connected to the plug socket in the wall.
- If the problem persists, contact the seller (information is given at the end of this card)
If you do not see power LED after switching on,try switching the controller on ON/OFF twice. If the controller still does not work contact the seller.
PRECAUTIONS
READ THE INSTRUCTIONS CAREFULLY BEFORE USING YOUR ELECTRIC BLANKET
- The heated area of any warming bedding should always lie flat.That is, it should never be bunched up, folded or balled up (e.g. between the mattress and the footboard) such that the heat generated in the middle of that ball has no place to escape.
- There should be nothing between the user’s body and the heated bedding except a thin bed-sheet.
- Turn off the bedding appliance when not in use.
- Do not use two electric blankets together for one person.
- Do not tug at the wires or use the cord as a handle.
- Do not use warming bedding alone with infants or very small children, people with disabilities, anyone who is immobile or cannot operate the controls properly, anyone insensitive to heat or anyone who cannot understand these directions.
- Do not allow petsto be around your warming bedding. A sharp claw or a tooth may puncture the wire insulation or damage the wiring itself.
- Do not use pins, nails around warming bedding. They can puncture the heater wire insulation.
- Never run the control cords between the mattress and the box springs. The cord could become damaged by friction or the heat from the electricity in the cord could be trapped there with no place to escape.
- Wrapping the cord around the controls may damage the cord. Loop loosely when storing.
- Never ironyour electric blanket. Ironing may damage the heating wire insulation.
- Never dry cleanor use cleaning fluid on your product. Dry cleaning agents contain solvents which may damage the heater wire insulation.
- Do not use an electric blanket on a waterbed.
- If you observe your electric blanket operating unusually or improperly (e.g. seems too hot in one area or you see a scorch mark) contact the manufacturer.
- Do not use with damaged cords.
- Keep the control away from drafty areas that may become damp or wet such as an open window.
- Be sure this blanket/mattress pad is used on 200-230 VAC supply.
- Do notconnect the heated product or use it until it is COMPLETELY dry.
- Do not use another electronic heating device in conjunction with your heated product or else both of them may get damaged.
- Do not use controller cable as a handle of the blanket.
